Відео

Remember, the wires are made with the correct, pre-determined number of separate wire strands bundled together to make sure they will carry the current safely. If you lose to many of them by not stripping them correctly, you run the risk of overloading the remaining wires. This could result in overheating the wires to the point of starting a fire!!!!!!!

Awesome! So helpful! Thanks!

Who is watching the point on that shove move back to Sunbury?

Why is bro moaning 💀

you mention at 16:25 you hear ticking. and ive read alot of people saying the older the subaru gets the more the injectors start to tick. doesnt mean that they are bad. but if you wanted to hear less tick sounds you can change out your injectors and it should make it a tad better. (rumor has it) also any update on the car???

PLEASE KEEP MAKING VIDEOS, i just learned alot

Denny is just trying so hard not to burst out laughing

Probably the easiest video I can find. Good job. Thanks

...ladies. 🤣

cut it off and buy a new one. probably cheaper than buying special tools lol

You can also take the little black cap off the top and blow thru it like a straw until a glob of ink comes out of the tip .

My bolt just stripped 💀

I appreciate the video, however, the Michael J Fox reference was insensitive.

mine had two small steel balls

please get a nail brush 😭

U fuck it up

Kyle then: **funny asl** Kyle now: **no personality**

Nice vid. Hey we're all fat guys working on our cars.😂😂😂😂🍺🍻🍻

Thank you! Favorite part….”ta-DA!!” 😂👏🏼👏🏼👏🏼🤩🤣 My pens do this crappy ALLLLL the time. It’s SOOOO annoying. 😤 This is Such a quick and easy fix. HaZAAA!! 😅🎉

So ended up being a rod knocking?

Mine has now been on for six years. No issues at all on my 2000 Subaru Forester.

Thank you!!

🎉

I litreally havent played with this wheel sincei was a kid, i just tried tto use it and it didn't calibrate i watched this video and it fixed it for me but the calibration wheel was loose so i tapped a little bit of glue on it so it would spin with the motor and bam t works perfect. reliving my child hood now GG thanks man

thanks for the help my testors paint was stuck and i was hoping for a very specific youtube fix video it was also green but different shade

What did u do the job? U did the job not right!

3:58

You missed Matt Kenseths intro to the game

My favorite Nascar game

Not gonna lie, larson is my new favorite driver.

That's the easiest bult to get off.. my issue the alignment bolt on both of my tire rods are so tight it's ridiculous from the manufacture.. has no rust at all..

Good job broski. Just what I needed

Are there 2 sets of V11 or what?

Is there a difference between the V11 20-870 and this V11 expansion pack?

Trying to install speakers into my 02 forester. All the other videos were confusing, but this one is simple and very helpful! Thank you so much!

Does the V11 set come with feeder track and a power pack or is that separate? Thanks for the review helps in deciding if this will work for me and my layout.

Dealer put these pieces of crap on our used car after we test drove it and went to pick it up after their “service” pissed me off. They are utter crap strut mounts bad at start and they creak now. Never asked the dealer to replace them. Pisses me off they won’t warranty them since we didn’t own the vehicle yet

Don’t know why I didn’t get the notification but holy hell was this funny 😂

loved playing the demo of this with the beach level.

Of course the idiot boyfriend probably had less than $200 to his name. The Sterling Company had the money and even then not enough to cover a multi-million dollar judgment against it.

Driver's side of the yeah. Understood completely.

GENIUS!

Who is here after Larson and Hamlin hate each other?

Lmao. “If I can find the hole….ladies”😂😂

The lawsuit was wrong to make the company pay for an idiots mistake.

I cut mine like this and it's still stuck, the tie rod won't come out, can anyone help me?

I think I'll be using this method here shortly 😊...Been messing with this one thing for 2 hours ... I'm over it.. The boot is already torn anyway... Just need to get it out so I can swap LBJ's... I'll order fresh outers...